Thursday, March 29, 2012

Mounting Router to Rousseau 3509 Plate

The router table and cabinet base are finished. I am now ready to mount a Sears 320.17542 fixed router to a Rousseau router plate. This Sears router was chosen for several reason among them are: one, it was on sale, two, 1/2" collet, three, above plate access to the lifting mechanism. The method discussed here should also work for aluminum plates.

In order to mount the router, a kit from Rousseau can be purchased, but since I had a PC type guide bushing with a 1/4" hole, I chose to purchase the following items from McMaster Carr:
  1. 98380A556  Dowel pin 1/4"
  2. 91420A330  Screw flathead M5.8 25mm
  3. 91217A175  Cone point socket screw M5.8 12mm
  4.  2739A38  Anti vibration thru-hole countersink, 90 deg., 3/16" - 17/32"
  5. 2915A22  Drill point countersink 5/64" - 3/16"
Your router may use a different screw size, but equivalent items should be available at McMaster.


A comment should be made before the step by step procedure. Phenolic plastic is very hard and not easy to scratch, so I tried two ways to get the set screws to mark the plate. First, I used a Bessey mini clamp, you can see them on the bench, to press the set screw into the plastic. I did this by placing the metal end of the clamp on the set screw and the handle end above the plate. Then I tightened the clamp. This worked for four of the set screws. Hitting the plate above the set screw transferred marks from the remaining two. 


Step by Step
  1. Remove plastic plate from bottom of router.
  2. Change to 1/4" chuck and add 1/4" dowel pin.
  3. Screw cone set screws into base as shown in picture
  4. Place guide bushing with 1/4" hole in plate
  5. Position router on bench as shown, with lift lock to front
  6. Place plate on router face up using dowel pin to center.
  7. Use spring clamps to hold router base to plate
  8. Use one of the methods above to cause cone set screws to mark plate
  9. Remove plate, find marks and enhance with center punch
  10. Use a small drill or drill point countersink to start hole.
  11. Drill hole out to screw body drill size, in my case a M5.8, 13/64"
  12. Turn plate over and counter sink hole using a single flute or thru-hole counter sink to proper depth
  13. Mount plate to router with flat head screws
  14. Using a scribe, mark lift hole on phenolic plate
  15. Drill 1/4" hole in plate and slightly counter sink on top side.







Router placed upside down on bench. Cone end set screws in place.


Closeup of set screw.


Guide bushing mounted in 3509 


Plate positioned on router. Note 1/4" dowel and guide bushing.


Drill point countersink in drill press chuck.


Router with plate mounted.


Flat head screws in place. Note lifter access hole at front.

Thursday, March 1, 2012

Router Table Base

This project describes the construction of a router table base cabinet. The construction of the Router table top. is shown on a separate post in this blog.

Router table base, sketch from notebook.

Almost completed router table base cabinet.


This sketch of the router table base is from a 8" by 5" Top Flight notebook which I use to track my project. As you can see, this design is like many that can be found on the Web, but you will find here a complete BOM and a step by step assembly in words and pictures.

The router table base is built with Kreg pocket screws, as many of the other projects in this blog. One lesson I have learned using the pocket screws is not to assume that two pieces of square cut wood assembled at right angles will be at right angle when the glue set. After the pieces are assembled, I use squaring blocks, as shown in the pictures below, to hold the pieces square until the glue sets, about an hour.


Step by Step Construction
    1. Make long cuts for sides, center and bottom panels 1/4" oversize, then trim to size
    2. Use a table saw sled to cut ends to length. A sled is a handy tool.
    3. Drill pocket holes in bottom and center panels on bottom.
    4. Screw and glue pieces together. Use squaring blocks while glue is setting.
    5. Drill pocket holes in drawer area verticals on inside of drawer area.
    6. Glue in place and use squaring blocks.
    7. Cut top cleats to size and drill pocket holes
    8. Screw and glue cleats in place to end panels and drawer verticals. Make sure drawer area width is equal top to bottom.
    9. Cut back support cleat to size and install under center panel. Glue.
    10. Cut 1/2" poplar to 3/4" width
    11. Glue and nail poplar to front edge of cabinet. Use 3/4" brads. 
    12. Sand cabinet, including front edge
    13. Round over all cabinet edges using a router and 1/8" round over bit
    14. Sand all edges lightly
    15. Seal all surfaces with Bulls Eye SealCoat
    16. Add back later.


    Bottom screwed to side with squaring blocks.

    Main components of base assembled.
    Back cleat to re-enforce center shelf.
    Drawer section verticals. Pocket holes on inside.
    Cabinet with 1/2" poplar front edging.

    BOM - Cabinet
    1. Side                   29 3/4" x 21 1/2"    qty 2
    2. Center/bottom    28 1/2" x 21 1/2"    qty 2
    3. Inside verticals   11 1/4" x 21 1/2"    qty 2
    4. Top cleats          3"        x 28 1/2"     qty 2
    5. Back cleat          3"        x 28 1/2"     qty 1
    6. Corner cleats                                    qty 2
    7. Caster strips       3"        x 30"           qty 2

    Making Drawers:

    Before the cabinet design was completed, the drawer area vertical height was determined. Three drawer sizes were chosen, 3", 3" and 4" and spacing of 1/4" top and bottom with 3/8" between drawers. This gives the following vertical drawer height:  1/4+3+3/8+3+3/8+4+1/4 = 11 1/4".

    The next need is to determine the position of the 20" Euro slides in the cabinet.  Because of the way the drawers are made the side mount Euro slide are easier to mount. For simplicity the slides are mounting on the center of the drawer side plus 1/8" ( Note 1). Next we must determine the position of slides in the cabinet assuming 3,3, and 4 drawer size from the top.
    1. 3" drawer: 1/4 + 1 1/2 = 1 3/4"
    2. 3" drawer: 1 3/4 + 1 1/2 + 3/8 + 1 1/2 = 5 1/8"
    3. 4" drawer: 5 1/8 + 1 1/2 + 3/8 + 2 = 9"
     To facilitate the following steps, place the cabinet on its left side on the bench. So measuring from the top of the vertical space, the first slide is at 1 3/4", the second at 5 1/8" and the last at 9". Since the drawer front will be indented, i.e., flush with the cabinet sides, the slides will be set back from the front by 9/16". The slide position lines need to be drawn perpendicular to the front cabinet edge and then a line drawn indented by 9/16" parallel to the front edge. See picture below. If you are not sure of these calculations, then lay them out on a piece of paper or scrap wood, including the top and bottom of each drawer.

    To mount the slides, position a left side cabinet slide with the front on the 9/16" line and along the position line with the line centered in the screw holes. Using a nail or a 1/16" center punch make a starter hole centered in the first small screw hole. Press a flat head screw into the hole and screw in place. Do the same at the far end using a small hole. Two screws per slide should be sufficient. Repeat the above with the right side drawer slides.


    Drawers: 3", 3" and 4"

    Slide positioning lines.

    Left side Euro slides mounted.
    To mount a slide to a 3" drawer, measure 1 5/8" from the top of the drawer and draw a line the length of the drawer. Lay a slide, make sure you have the correct one, along the line with the front of the slide even with the drawer front. Screw it in place. Try the drawer in the top position. It should clear the top by 1/4". Repeat this process with the other drawers, except for the 4" drawer, draw the line at 2 1/8".. There should be a 3/8" clearance between drawers.

    Measure 1 5/8" from top of the 3" drawer both ends.

    Mark line on side of drawer.

    Making the Drawer Fronts:

    The following method works for both full extension and Euro slides.

    Step 1: From 1/2 (12 mm) plywood cut the front 1/4" smaller than the horizontal opening and 1/4" larger than the nominal drawer height. 

    Step 2: With a 1/8"R  round over bit dress the front edge of the drawer front. After filling any voids in the edge sand and seal the drawer front both sides. Then coat with polyurethane.

    Drawer front marked for handle.
    Step 3: Find vertical and horizontal of the drawer front and mark with pencil. Using center punch, mark position of handle holes. Then drill holes using a 3/16" brad pointed or dowel bit to prevent tearing around hole. 

    Front drilled for handle.
    Step 4: Clamp the drawer front to front part of the drawer. Use 1/8" spacers at bottom edge and center the front. Use a mini clamp to hold front in place will handle holes are drilled through. Insert handle screws from inside draw and fastened handle. If it was a wide drawer, 3/16" holes would be drilled through the front of the drawer at each end, then 3/4" #8 screws would be used to hold the drawer front in place. After that, drill and mount the handle. 

    Squeeze clamp holding drawer front in place with 1/8" spacer at bottom edge.
    : 
    Front positioned and ready to be drilled.
    Finished drawer front.
    Step 4: The method used above will not work for the top draw, so I use two small pieces of carpet tape on the front of the drawer. A spacer is used to space the drawer fronts. Set the drawer front at an angle on the spacer then tip the front forward until the tape is contacted. Clamp and drill handle holes.

    Using carpet tape. Note 1/8" spacers.
    BOM Drawers

        3" Drawer:
      1. Sides:          qty 2, 2 13/16" x 16" x 1/2"
      2. Front/Back: qty 2, 2 13/16" x 5 9/16" x 1/2"
      3. Bottom:       qty 1, 5 9/16" x 16" x 3/16"
        4" Drawer:
      1. Sides:     qty 2, 3 13/16" x 16" x 1/2"
      2. Front
      3. Bottom:
        Misc:
      1. 20" Side mount Euro Slides,  Liberty  D66320C-W-TS, HD
      2. Kreg 1" pocket screws
      3. Glue


       Material: 12mm (15/32") Blonde Plywood from Lowes or equivalent.
      Casters:


      For a small shop it is very handy to be able to move tool cabinets around. Casters have been added to most of the projects on this blog, but they all have a common failing, they move a little even if locked. The router cabinet with the router installed has a low center of gravity, so on this cabinet two rigid caster and two short legs have been used. Another choice would be to use two levelers in place of the legs. To move the cabinet simply lift the end with the legs off the floor and roll on the caster. I would worry about using this method on cabinets with a high center of gravity like with a bench drill press because lifting one end might tip the hole thing. The method may work with the miter cabinet.

      Legs and 2" rigid casters

      Legs cut from 1 1/2" poplar and mounted with a 5/16" x 3 1/2" lag bolt.

      Electric:

      The electric consists of a front mounted switch and an internal duplex outlet. The switch turns both the router and a vacuum on together. Initially, a wall type switch will be used, but will be replaced by the Grizzily switch shown below which is designed to mount on a standard electric box.

      Electric boxes to be mounted. Note bracket.


      Bracket for switch box.

      Switch mounted.

      Power cord dressed at back of drawer area.

      Duplex outlet and power cord.


      Switch that will mount in standard electric box as shown in above picture.






        Thursday, February 23, 2012

        Multi-Drawer Home Office Cabinet

        Multi Drawer Shop Cabinet

        Except for my Craftman tool box, My shop had no drawers which is one reason that drawers are being added to all the shop projects. 


        BOM
        1. Top/Bottom: qty 2,  24 1/2" x 19 1/2"
        2. Sides: qty 2, 21 1/2" x 19 1/2"
        3. Cleats: qty 2, 4 1/2" x 25 1/2"
        4. Caster blocks: qty 4, 4" x 3"
        5. Casters: 2"
        Drawers:
        1. Sizes:   2", 3", 4", 4", 5"
        2. Spacing Top/Bottom: 1/4"
        3. Spacing between drawers: 3/8"
        4. Vertical drawer space: 1/4 + 2 + 3/8 + 3 + 3/8 + 4 + 3/8 + 4 + 3/8 + 5 + 1/4 = 20"
        5. Slide Positions: 1 1/4", 4 1/8", 8", 12 3/8", 17 1/4"
        6. Slide type: full extension Liberty D80618C-ZP-W
        7. Drawer depth/width: 18 1/2" / 23 1/2"

        Monday, February 13, 2012

        Euro Drawer Slide Mounting

        If a full extension slide is not required, the Euro slide at less than half the cost can be used. The discussion here assumes the use of side mounted Euro drawer slides, not bottom corner slides. Because we are using side mounts, the full extension drawer slide method can be used with two exceptions:
        1. On the Euro slide the screw holes in drawer part are 5/32 lower than the holes in the cabinet part where the screw holes in the full extension ball bearing slide are aligned. Check it out.
        2. The Euro slides are not full extension, so the drawer depth is about 4" shorter than the slide length unless part of the drawer remaining in the cabinet is acceptable. In the picture below, the drawer is 16" deep using 18" slides.
         For a full discussion of drawer mounting see the post on full extension slide; however, below find pictures of drawers mounted with Euro slides. In these pictures the slide is mounted on the drawer at approximately 3/4 of nominal draw height which for the 4" drawer is 3" and 5 1/8" drawer 4". On the drawer an additional 1/8" ( 5/32") must be added to adjust for screw hole vertical alignment. The cabinet slides are at the following positions measured from the top of the opening where the drawers are 4" and 5 1/8" in height.
        1. Top Drawer: 1/4" + 3" = 3 1/4"
        2. Second Drawer:  1/4" + 4" + 3/8" + 4" = 8 5/8"
        For the slide positions on the drawers:
        1. Top: 3 1/8" from top of drawer
        2. Second: 4 1/8"
        where the 1/8" (5/32") compensates for the hole alignment.

        One more note, when mounting the slides in the cabinet, use one screw at the back and one screw in the vertical slot in the front of the slide to allow for final adjustment. When you finally get to the point of mounting the fronts to the drawers and aligning the seams around the drawers one or both of the cabinet slides may need to be moved up or down a little to even the horizontal seams.

        Front view

        With drawer at full extension. 20" slides with 18" drawer

        Simplified Drawer Construction

        After making several drawers for shop cabinets, the following procedure has been worked out.

        Procedure Steps:
        1. Cut sides from 1/2" plywood
        2. Drill pocket holes in the front and back pieces
        3. Using jig, glue and screw sides
        4. Use corner blocks and clamps to square up drawer
        5. Cut bottom from 3/16" plywood
        6. Glue and nail to drawer bottom
        To make a 4" high drawer that is 16" deep by 22 1/2" wide. This is a drawer used in the bandsaw cabinet and is mounted with 18" euro slides. These slides are not full extension, so about 2" of the drawer remains in cabinet. The plywood used for the bottom was 3/16" thick underlayment plywood sold at HD with the back of the plywood face up in the drawer. The sides were cut from 1/2" Blonde plywood from Lowes which has been pre-cut to 4 ft by 2 ft panels for easy car transport.

        Step by Step Drawer Construction

        1. Cut four side pieces 3 13/16" wide from 2 ft wide, 1/2" panel (note1)
        2. Clamp two pieces together, aligning the edges
        3. Use miter saw to trim one end to square (note2)
        4. With straight edge, mark pieces at 16" and cut with miter saw
        5. Clamp the other two pieces, repeat above steps but measure to 21 9/16" (front, rear) (note3)
        6. With Kreg fixture drill front and rear with two pocket holes per end
        7. Place a side piece on the bench, clamp as shown in the picture (note5)
        8. Clamp jig at end of piece
        9. Spread glue on front piece end, place against jig and side piece. Clamp in place. (note6)
        10. Fasten with 1" Kreg screws, do not over tighten. Use drill break.
        11. Repeat steps 9 and 10 for other pieces.
        12. With box complete use squaring blocks and clamps to guaranty squareness.
        13. Cut bottom to size and glue and nail (5/8" brads) in place.
        14. Sand sides and edges, then round over with 1/8 roundover router bit 
        15. Finish with a good hand sanding
        16. Sealcoat drawer and finish inside with polyurethane.

        Notes:

        1. To cut width accurately, make table saw test cuts in 3/16 ply scrapes.
        2. This Blonde plywood surface splinters easily, so take your time or place a piece of scrap wood under piece being cut.
        3. Measure after cutting and make sure length is within 1/32"
        4. Use the 1/2" Kreg guide block and drill
        5. The front and back pieces fit between the side pieces making the drawer width 22 1/2"
        6. All this clamping is necessary to keep the front piece from pulling out of place when the screws are tightened. This happens because the screws are going in at an angle and want to pull the piece out of place as the screws are turned..


        Kreg pocket hole jig with 1/2" guide block



        Pieces clamped in place with jig ready for screws

        Clamp jig closeup.

        Squaring corner clamp blocks

        Shows drawer with bottom glued and nailed on.

        Full Extension Drawer Slide Mounting

        The method we use for installing a stack of drawers in frameless cabinets assumes the following:
        1. Drawer fronts will indent into opening
        2. The spacing around the drawer front edge and cabinet wall will be 1/8"
        3. The drawer slides will be side mounted
        4. The top and bottom drawer will have a 1/4" clearance with the drawer opening cabinet edge
        5. The spacing between drawers will be 3/8"
        6. The drawer front height will be 1/4" larger than nominal drawer vertical size,i.e., a 1/8" lip
        The picture below shows an example cabinet with 5 drawers using this method. The above dimensions provide a 1/8" lip for the drawer front relative to the drawer body.

        5 Drawer cabinet on wheels using full extension slides.
        The first step is to determine cabinet slide positions for the drawer set. For example, the drawers shown above are: 2", 3", 3", 4" and 5". With the drawer slides mounted centered on the drawer sides, the following arithmatic will determine the slide positions:
        1. 2" drawer: 1/4 + 1 = 1 1/4", 1/4" for top spacing + 1" for 1/2 the drawer height.
        2. 3" drawer: 1 1/4 + 1 + 3/8 + 1 1/2 = 4 1/8", (2" drawer position) 1 1/4 + (remain drawer width) 1 +  (drawer spacing) 3/8 + (1/2 3" drawer height) 1 1/2
        3. 3" drawer: 4 1/8 + 1 1/2 + 3/8 + 1 1/2 = 7 1/2"
        4. and so on.
        So we have the following positions: 1 1/4", 4 1/8", 7 1/2". The next step is to mark these positions on the inside side of the cabinet measured from the inside top of the opening as shown below. The slides must be indented 9/16" from the front edge so when completed the drawers sit flush with cabinet front.

        Step 3: position slide on a line centered in the screw holes. Mark two or three hole positions and use a nail or center punch ( I like a 1/16" center punch McMaster #34155A11 ) to make a starter hole for the screw, then screw slide in place.


        Mounting cabinet full extension slides.
        Step 4: Mounting slide to drawer side. At either end of the drawer make a mark at 1/2 the drawer height and then draw the line.
        Marking slide position on drawer.
        Drawing slide position line.
        Screwing slide to drawer.
        Step 5: Position slide on drawer with slide end aligned to drawer front as shown. Make starter holes and screw slide in position. Repeat for other drawer side.

        Step 6: Insert the drawer into the cabient slides. When you push the drawer into position the first time you will encounter some resistance, since the bearings are repositioning themselves. Once the drawer is inplace this resistance should not occur. A couple of drops of DuPont Silicone lubricant on each slide before insertion will work wonders.

        Making the Drawer Fronts:

        The following method works for both full extension and Euro slides.

        Step 1: From 1/2 (12 mm) plywood cut the front 1/4" smaller than the horizontal opening and 1/4" larger than the nominal drawer height. 

        Step 2: With a 1/8"R  round over bit dress the front edge of the drawer front. After filling any voids in the edge sand and seal the drawer front both sides. Then coat with polyurethane.

        Drawer front marked for handle.
        Step 3: Find vertical and horizontal of the drawer front and mark with pencil. Using center punch, mark position of handle holes. Then drill holes using a 3/16" brad pointed or dowel bit to prevent tearing around hole. 

        Front drilled for handle.
        Step 4: Clamp the drawer front to front part of the drawer. Use 1/8" spacers at bottom edge and center the front. Use a mini clamp to hold front in place will handle holes are drilled through. Insert handle screws from inside draw and fastened handle. If it was a wide drawer, 3/16" holes would be drilled through the front of the drawer at each end, then 3/4" #8 screws would be used to hold the drawer front in place. After that, drill and mount the handle. 

        Squeeze clamp holding drawer front in place with 1/8" spacer at bottom edge.
        : 
        Front positioned and ready to be drilled.
        Finished drawer front.
        Step 4: The method used above will not work for the top draw, so I use two small pieces of carpet tape on the front of the drawer. A spacer is used to space the drawer fronts. Set the drawer front at an angle on the spacer then tip the front forward until the tape is contacted. Clamp and drill handle holes.